What a hot water system costs in Moreton Bay
Updated October 2026
Prices below are typical 2026 installed ranges for Moreton Bay and South East Queensland. Every home is different, so treat these as a guide and get a fixed quote before work starts. The plumber's own quote is the price that counts.
Quick price guide, installed
- Repairs (valves, elements, thermostats, pilot lights): roughly $150 to $600 depending on the part
- Electric storage replacement, like for like: from around $800 to $2,500
- Gas storage replacement: from around $1,200 to $3,500
- Continuous flow (instantaneous) gas: from around $1,200 to $3,500
- Heat pump: around $3,000 to $6,000 before incentives, and incentives can take thousands off, so always ask for the net installed price
- Solar: the highest upfront cost, quoted per roof and household
What moves the price
Four things change a hot water bill: the system type, the size (a 250L tank for a family costs more than a 125L for a couple), whether the new system matches the old connections, and access. In Moreton Bay, access deserves its own line. A tank in an easy carport at Clontarf or Kippa-Ring is the cheap end. A unit up a flight of stairs in a Redcliffe apartment, a terraced block at Eatons Hill, or an underhouse space in an Arana Hills split-level takes longer to swap, and the quote reflects it. Changing fuel type, relocating the unit, or upgrading the electrical circuit or gas line also adds to the price. After-hours work costs more than a booked job, so if you have some hot water left, booking tomorrow morning beats paying tonight's rate.
Coastal, rural and travel factors
Homes near the water at Redcliffe, Scarborough, Beachmere and across Bribie Island often need corrosion-resistant fittings or a more sheltered position for the new unit, which can add a little to the job. Out in the rural west at Dayboro, Wamuran, Woodford and D'Aguilar, some quotes include an allowance for travel, and properties on tank water may need filtration or pressure work considered as part of the job. None of that is a reason to pay more than a fair price, but it explains why two quotes in the region can differ.
The incentive question
Heat pump hot water attracts federal Small-scale Technology Certificates (STCs) on eligible, approved models, and they genuinely change the maths: a system with a large sticker price can land much closer to a conventional replacement once the certificates are applied. The installer claims them for you and the certificate value moves with the market, so the only number that matters is the net installed price on your quote. Ask for it in writing, and ask what brand and model the price is based on. State and federal programs change from time to time, so ask the installer what applies at the time you buy rather than relying on a figure you read somewhere.
Repair or replace, by the numbers
Spending $400 repairing a 4-year-old system is good money. Spending $400 on a 12-year-old tank that will leak within a year or two is not. The plumbers we work with will tell you the age and condition of your system and give you both numbers, the repair and the replacement, so you can make the call yourself.
Frequently asked questions
How long does a replacement take?
A like-for-like swap is usually done in two to four hours once the plumber has the system on the truck. Same-day replacement is often possible for common sizes if you get in early in the day. Difficult access adds time.
Is it illegal to install my own hot water system?
In Queensland, yes. Plumbing is licensed work and hot water installation must be done by a QBCC-licensed plumber, gas systems need a licensed gas fitter, and hard-wired electric connections need a licensed electrician. DIY installation can also void insurance and warranty.
What size tank do I need?
As a rough rule: 125L to 160L suits one to two people, 250L suits three to four, and 315L suits larger households. Continuous flow systems are sized by flow rate instead, usually 20 to 26 litres per minute for a family home.